goto rvbd;\r
//-------------------------------------------------//\r
case H_SPUirqAddr:\r
+ //if (val & 1)\r
+ // log_unhandled("w irq with lsb: %08lx %04x\n", reg, val);\r
spu.pSpuIrq=spu.spuMemC+(((unsigned long) val<<3)&~0xf);\r
goto upd_irq;\r
//-------------------------------------------------//\r
break;\r
//-------------------------------------------------//\r
\r
+ case H_SPUmvolL:\r
+ case H_SPUmvolR:\r
+ if (val & 0x8000)\r
+ log_unhandled("w master sweep: %08lx %04x\n", reg, val);\r
+ break;\r
+\r
+ case 0x0dac:\r
+ if (val != 4)\r
+ log_unhandled("1f801dac %04x\n", val);\r
+ break;\r
+\r
/*\r
case H_ExtLeft:\r
//auxprintf("EL %d\n",val);\r
{\r
const int ch=(r>>4)-0xc0;\r
if(spu.dwNewChannel&(1<<ch)) return 1; // we are started, but not processed? return 1\r
- if((spu.dwChannelOn&(1<<ch)) && // same here... we haven't decoded one sample yet, so no envelope yet. return 1 as well\r
+ if((spu.dwChannelsAudible&(1<<ch)) && // same here... we haven't decoded one sample yet, so no envelope yet. return 1 as well\r
!spu.s_chan[ch].ADSRX.EnvelopeVol)\r
return 1;\r
return (unsigned short)(spu.s_chan[ch].ADSRX.EnvelopeVol>>16);\r
//case H_SPUIsOn2:\r
// return IsSoundOn(16,24);\r
\r
+ case H_SPUMute1:\r
+ case H_SPUMute2:\r
+ log_unhandled("r isOn: %08lx\n", reg);\r
+ break;\r
}\r
\r
return spu.regArea[(r-0xc00)>>1];\r
\r
for(ch=start;ch<end;ch++,val>>=1) // loop channels\r
{\r
- if((val&1) && regAreaGet(ch,6)) // mmm... start has to be set before key on !?!\r
+ if((val&1) && regAreaGetCh(ch, 6)) // mmm... start has to be set before key on !?!\r
{\r
spu.s_chan[ch].bIgnoreLoop = 0;\r
spu.dwNewChannel|=(1<<ch);\r
if(vol&0x8000) // sweep?\r
{\r
short sInc=1; // -> sweep up?\r
+ log_unhandled("ch%d sweepl %04x\n", ch, vol);\r
if(vol&0x2000) sInc=-1; // -> or down?\r
if(vol&0x1000) vol^=0xffff; // -> mmm... phase inverted? have to investigate this\r
vol=((vol&0x7f)+1)/2; // -> sweep: 0..127 -> 0..64\r
if(vol&0x8000) // comments... see above :)\r
{\r
short sInc=1;\r
+ log_unhandled("ch%d sweepr %04x\n", ch, vol);\r
if(vol&0x2000) sInc=-1;\r
if(vol&0x1000) vol^=0xffff;\r
vol=((vol&0x7f)+1)/2; \r
if(val>0x3fff) NP=0x3fff; // get pitch val\r
else NP=val;\r
\r
- spu.s_chan[ch].iRawPitch=NP;\r
- spu.s_chan[ch].sinc=(NP<<4)|8;\r
- spu.s_chan[ch].sinc_inv=0;\r
- if (spu_config.iUseInterpolation == 1)\r
- spu.SB[ch * SB_SIZE + 32] = 1; // -> freq change in simple interpolation mode: set flag\r
+ spu.s_chan[ch].iRawPitch = NP;\r
+ spu.s_chan[ch].sinc = NP << 4;\r
+ spu.s_chan[ch].sinc_inv = 0;\r
+ spu.s_chan[ch].bNewPitch = 1;\r
+\r
+ // don't mess spu.dwChannelsAudible as adsr runs independently\r
}\r
\r
////////////////////////////////////////////////////////////////////////\r