+/*
+ * <random_info=mem_map>
+ * 00000000-029fffff linux (42MB)
+ * 02a00000-02dfffff fb (4MB, 153600B really used)
+ * 02e00000-02ffffff sound dma (2MB)
+ * 03000000-03ffffff MPEGDEC (?, 16MB)
+ * </random_info>
+ */
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include "soc.h"
#include "plat_gp2x.h"
#include "../common/emu.h"
+#include "../common/plat.h"
#include "../common/arm_utils.h"
#include "pollux_set.h"
static volatile unsigned short *memregs;
-static volatile unsigned long *memregl;
+static volatile unsigned int *memregl;
static int memdev = -1;
static int battdev = -1;
static int last_pal_setting = 0;
+/* misc */
+static void pollux_set_fromenv(const char *env_var)
+{
+ const char *set_string;
+ set_string = getenv(env_var);
+ if (set_string)
+ pollux_set(memregs, set_string);
+ else
+ printf("env var %s not defined.\n", env_var);
+}
+
/* video stuff */
static void pollux_video_flip(int buf_count)
{
int code = 0, bytes = 2;
int rot_cmd[2] = { 0, 0 };
unsigned int r;
+ char buff[32];
int ret;
if (bpp == prev_bpp)
memregl[0x4000>>2] |= 1 << 3;
/* the above ioctl resets LCD timings, so set them here */
- set_lcd_custom_rate(last_pal_setting);
+ snprintf(buff, sizeof(buff), "POLLUX_LCD_TIMINGS_%s", last_pal_setting ? "PAL" : "NTSC");
+ pollux_set_fromenv(buff);
switch (abs(bpp))
{
cpuclk_was_changed = 1;
}
-/* misc */
-static void pollux_set_fromenv(const char *env_var)
-{
- const char *set_string;
- set_string = getenv(env_var);
- if (set_string)
- pollux_set(memregs, set_string);
- else
- printf("env var %s not defined.\n", env_var);
-}
-
/* RAM timings */
static void set_ram_timings_(void)
{
/* LCD refresh */
static void set_lcd_custom_rate_(int is_pal)
{
- char buff[32];
-
- snprintf(buff, sizeof(buff), "POLLUX_LCD_TIMINGS_%s", is_pal ? "PAL" : "NTSC");
- pollux_set_fromenv(buff);
+ /* just remember PAL/NTSC. We always set timings in _changemode_ll() */
last_pal_setting = is_pal;
}
}
}
+#define TIMER_BASE3 0x1980
+#define TIMER_REG(x) memregl[(TIMER_BASE3 + x) >> 2]
+
+unsigned int gp2x_get_ticks_us_(void)
+{
+ TIMER_REG(0x08) = 0x4b; /* run timer, latch value */
+ return TIMER_REG(0);
+}
+
+unsigned int gp2x_get_ticks_ms_(void)
+{
+ /* approximate /= 1000 */
+ unsigned long long v64;
+ v64 = (unsigned long long)gp2x_get_ticks_us_() * 4294968;
+ return v64 >> 32;
+}
+
+static void timer_cleanup(void)
+{
+ TIMER_REG(0x40) = 0x0c; /* be sure clocks are on */
+ TIMER_REG(0x08) = 0x23; /* stop the timer, clear irq in case it's pending */
+ TIMER_REG(0x00) = 0; /* clear counter */
+ TIMER_REG(0x40) = 0; /* clocks off */
+ TIMER_REG(0x44) = 0; /* dividers back to default */
+}
+
+/* note: both PLLs are programmed the same way,
+ * the databook incorrectly states that PLL1 differs */
+static int decode_pll(unsigned int reg)
+{
+ long long v;
+ int p, m, s;
+
+ p = (reg >> 18) & 0x3f;
+ m = (reg >> 8) & 0x3ff;
+ s = reg & 0xff;
+
+ if (p == 0)
+ p = 1;
+
+ v = 27000000; // master clock
+ v = v * m / (p << s);
+ return v;
+}
+
void pollux_init(void)
{
struct fb_fix_screeninfo fbfix;
- int i, ret;
+ int i, ret, rate;
memdev = open("/dev/mem", O_RDWR);
if (memdev == -1) {
if (battdev < 0)
perror("Warning: could't open pollux_batt");
+ /* find what PLL1 runs at, for the timer */
+ rate = decode_pll(memregl[0xf008>>2]);
+ printf("PLL1 @ %dHz\n", rate);
+ rate /= 1000000;
+
+ /* setup timer */
+ if (1 <= rate && rate <= 256) {
+ if (TIMER_REG(0x08) & 8) {
+ fprintf(stderr, "warning: timer in use, overriding!\n");
+ timer_cleanup();
+ }
+
+ TIMER_REG(0x44) = ((rate - 1) << 4) | 2; /* using PLL1, divide by it's rate */
+ TIMER_REG(0x40) = 0x0c; /* clocks on */
+ TIMER_REG(0x08) = 0x6b; /* run timer, clear irq, latch value */
+
+ gp2x_get_ticks_ms = gp2x_get_ticks_ms_;
+ gp2x_get_ticks_us = gp2x_get_ticks_us_;
+ }
+ else {
+ fprintf(stderr, "warning: could not make use of timer\n");
+
+ // those functions are actually not good at all on Wiz kernel
+ gp2x_get_ticks_ms = plat_get_ticks_ms_good;
+ gp2x_get_ticks_us = plat_get_ticks_us_good;
+ }
+
pllsetreg0 = memregl[0xf004>>2];
memtimex_old[0] = memregs[0x14802>>1];
memtimex_old[1] = memregs[0x14804>>1];
gp2x_video_RGB_setscaling = gp2x_video_RGB_setscaling_;
gp2x_video_wait_vsync = gp2x_video_wait_vsync_;
- gp2x_set_cpuclk = gp2x_set_cpuclk_;
+ /* some firmwares have sys clk on PLL0, we can't adjust CPU clock
+ * by reprogramming the PLL0 then, as it overclocks system bus */
+ if ((memregl[0xf000>>2] & 0x03000030) == 0x01000000)
+ gp2x_set_cpuclk = gp2x_set_cpuclk_;
+ else {
+ fprintf(stderr, "unexpected PLL config (%08x), overclocking disabled\n",
+ memregl[0xf000>>2]);
+ gp2x_set_cpuclk = NULL;
+ }
set_lcd_custom_rate = set_lcd_custom_rate_;
unset_lcd_custom_rate = unset_lcd_custom_rate_;
memregl[0xf004>>2] = pllsetreg0;
memregl[0xf07c>>2] |= 0x8000;
}
+ timer_cleanup();
munmap((void *)memregs, 0x20000);
close(memdev);
notaz.gp2x.de / libpicofe.git / blobdiff